[arm-allstar] TX audio
Doug Crompton
doug at crompton.com
Thu Oct 23 16:44:44 EST 2014
On the BBB TXA has always been voice and TXB no, if it is different then it is something that a user changed.
txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice
; no - Do not output anything
; voice - output voice only
txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice
; See txmixa above.
73 Doug
WA3DSP
http://www.crompton.com/hamradio
From: w5jr.mike at gmail.com
Date: Thu, 23 Oct 2014 17:29:31 -0400
To: arm-allstar at hamvoip.org
Subject: Re: [arm-allstar] v1.2 Install DTMP Issue
Check to see which TX path in simpleusb.conf has the audio on it, TX-A or TX-B. I *believe* that Ver 1 put the default TX audio on B where as I've usually seen TX audio on A and any separate sub tone (CTCSS) on B. I had to change my simpleusb.conf file setting to match the previously wired cable to my URIx. Also, if you are adjusting the TX level, be sure you are adjusting A or B as appropriately wired.
tnxMike / W5JR
On Oct 23, 2014, at 3:38 PM, "Joe Zynel" <jzynel at comcast.net> wrote:
Doug, Thanks for all your help. I am talking about the audio coming from the radio connected to the BBB which transmits back to my HT. So the node TX out. The level is lower than another node I have when I switch between the two. No biggie I can crank up the volume on the HT to compensate. I had lsnodes on my other node. Nice to see it is installed. I will try it out. ThanksJoeN3FHW From: arm-allstar-bounces at hamvoip.org [mailto:arm-allstar-bounces at hamvoip.org] On Behalf Of Doug Crompton
Sent: Thursday, October 23, 2014 3:33 PM
To: BeagleBone Black ARM Allstar
Subject: Re: [arm-allstar] v1.2 Install DTMP Issue Joe,
Just so I understand because people often confuse TX and RX depending on how they are looking at it. Are you referring to selection 2 on the simpleusb-tune-menu program where you see the audio in a graph display on the screen? This is the audio FROM your node radio, the node radios RX and is seen when you TX on a handheld or another radio TO your node radio. The stock setting in simpleusb.conf is rxboost=1 which is on. Perhaps wherever you are taking the audio from your node radio RX output is to low a level? It should be at least 100mv P-P.
For lsnodes it is already setup on the BBB. I believe that is described on the web page but I am going to be doing some reworking of the web page soon and I will probably add that as a howto. Anyhow all you have to do is the following line in your browser. The browser should be firefox, waterfox, or chrome, NOT explorer.
192.168.0.132/cgi-bin/lsnodes_web?node=40638
In the above line change the IP address to the local IP address of your BBB and change the node to the node number of your BBB. If you wanted to use this externally you would have to forward port 80 in your router to the BBB and use your public IP address. You could change the port by configuring the httpd config if you didn't want to use port 80.
For a description of lsnodes see - http://crompton.com/hamradio/allstar/lsnodes.html
but note that you do not need to install anything so you can disregard anything about that. The page was written for the acid release.
73 Doug
WA3DSP
http://www.crompton.com/hamradio
From: jzynel at comcast.net
To: arm-allstar at hamvoip.org
Date: Thu, 23 Oct 2014 14:41:31 -0400
Subject: Re: [arm-allstar] v1.2 Install DTMP IssueDoug, Thanks for everything. I got it up and running. Node 41362. I had one other question. I used simpleusb-tune-menu to set the RX. Even when I put TX to 999 the audio is still low. Is there somewhere else to adjust the tx audio besides simpleusb-tune-menu? Also, is the documentation updates on the scripts on the image? Is lsnodes on there? Thanks JoeN3FHW _________________________________________________________________
W. Joseph Zynel | General Adjuster | Zynel Adjusting Inc.
+P.O. Box 318 | Hampstead, MD 21074 | (: 410.239.0107 (O) | 7: 410.239.0108 (F)
*: jzynel at zynel.com | :: http://www.zynel.com | ): 443.904.5676 (M)CLICK HERE TO GET MY V-CARD The information contained in this communication may be confidential, is intended only for the use of the recipient named above, and may be legally privileged. If the reader of this communication is not the intended recipient, you are hereby notified that any dissemination, distribution, or copying of this communication, or any of its contents, is strictly prohibited. If you have received this communication in error, please re-send this communication to the sender and delete the original message and any copy of it from your computer system. From: arm-allstar-bounces at hamvoip.org [mailto:arm-allstar-bounces at hamvoip.org] On Behalf Of Doug Crompton
Sent: Thursday, October 23, 2014 1:21 AM
To: BeagleBone Black ARM Allstar
Subject: Re: [arm-allstar] v1.2 Install DTMP Issue Joe,
The best way to troubleshoot this is to go into the client -
asterisk -rvvv
at the linux prompt
Then keyup and hit DTMF keys. The log should show the key value. It will look like this:
bbb-allstar*CLI>
[Oct 23 01:20:00] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 1
[Oct 23 01:20:01] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 2
[Oct 23 01:20:02] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 3
[Oct 23 01:20:03] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 4
[Oct 23 01:20:03] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 5
[Oct 23 01:20:04] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 6
[Oct 23 01:20:05] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 7
[Oct 23 01:20:06] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 8
[Oct 23 01:20:07] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 9
[Oct 23 01:20:08] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char 0
[Oct 23 01:20:09] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char *
[Oct 23 01:20:09] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char #
[Oct 23 01:20:11] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char A
[Oct 23 01:20:12] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char B
[Oct 23 01:20:13] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char C
[Oct 23 01:20:13] NOTICE[432]: chan_simpleusb.c:2893 simpleusb_read: Got DTMF char D
Did you run simpleusb-tune-menu and set the audio levels as per the configuration how-to?
73 Doug
WA3DSP
http://www.crompton.com/hamradioDate: Thu, 23 Oct 2014 00:10:08 +0000
From: jzynel at comcast.net
To: arm-allstar at hamvoip.org
Subject: [arm-allstar] v1.2 Install DTMP Issue
Doug, I installed V1.2 today and it is working except when I do DTMF commands. In one of about 10 tries I connect. But I cannot disconnect and do any of the other DTMF functions. I am using a USB FOB with a Baofeng UV-5r. Thanks for the helpJoeN3FHW
_______________________________________________ arm-allstar mailing list arm-allstar at hamvoip.org http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
___________________________
____________________ arm-allstar mailing list arm-allstar at hamvoip.org http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/_______________________________________________
arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
_______________________________________________
arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20141023/24915485/attachment-0001.html>
More information about the arm-allstar
mailing list